Mating tip
Define diameter, usable length, lead-in geometry and finished condition.
AI-generated engineering concept — not a production photograph. Final geometry is defined by your drawing.
ENGINEERING CONCEPT / cs-product-066
Coaxial center contact
A turned center-contact concept with a solid mating tip and rear termination cup: review the contact diameters, insulator seat and finished surface together.
- Buyer application
- Sensors & instrumentation
- Reference type
- AI-generated geometry concept
- Material & process
- Options to review against your drawing
- Dimensions & tolerances
- Defined by your approved drawing
AI-generated engineering concept for a custom component discussion. It is not a production photograph, delivery case or completed inspection record.
FROM FORM TO A MANUFACTURING BRIEF
Supply the specified mechanical center contact for a separately validated connector assembly.
A turned center-contact concept with a solid mating tip and rear termination cup: review the contact diameters, insulator seat and finished surface together.
01
Define the mating and insulator interfaces
Identify the mating tip, the insulator locating diameter and the shoulder that controls axial position. Supply the corresponding socket and insulator limits or a controlled interface drawing, together with the intended assembly sequence. This concept uses a solid male tip and a rear termination cup; it is not a spring contact or an assembled coaxial connector. The metal geometry is one input to the complete interconnect. No characteristic impedance, frequency range, insertion loss, power rating or mating life is established by the illustrated contact.
02
Specify the surface that will actually be assembled
State the approved base alloy, any underplate and final coating requirements, including the dimensions that apply after plating. Define the working tip length, entry radius, shoulder position and termination-cup bore. If a side access opening is required for termination, show its location and the edge condition inside the cup. Ask for the quoted scope to identify plating, cleaning and inspection responsibilities clearly. A uniform gold-colored image is not evidence of a specific coating thickness, conductivity or contact-resistance result on an actual part.
03
Connect dimensional approval to the connector test
Agree checks for the finished mating diameter, insulator seat, axial stack and accessible termination geometry. Identify any plating documentation or material traceability required with the sample lot. Connector insertion, retention, electrical and radio-frequency tests should use the completed assembly under the defined buyer procedure. Keep their acceptance separate from the dimensional release of the contact. Protect the mating surfaces in packing and avoid uncontrolled bulk contact during handling. Review changes to insulator, mating socket, base material or coating before repeating the contact order. Keep the approved sample reference.
MATERIAL & PROCESS REVIEW
Select the material for the drawing and service
These are candidates to discuss, not an approved material specification. Confirm the grade, condition and final finish before quotation.
- Phosphor bronze
- Consider only where the connector design approves the grade, termination process and final coating; do not infer electrical performance from the alloy name.
- Brass
- Consider only where the connector design approves the alloy, final coating and termination process.
The illustration does not establish a material grade, tolerance, coating or tested performance. Confirm these in your drawing and acceptance plan.
BEFORE APPROVING A SAMPLE
Agree what the checks need to establish.
Insulator seat
Control locating diameter and shoulder position to the mating interface.
Termination cup
Specify cup depth, wall and access opening with internal edge requirements.
Coating allowance
Agree dimensions after plating and required finish documentation.
BEFORE YOU RELEASE THE DRAWING
A practical next step.
Use these guides to define the records and checks your component needs.
Swiss Turning Bar Stock: Match the Material to the Guide Bushing
For Swiss-turned parts, agree bar diameter variation, straightness and surface condition with the actual guide-bushing system before buying stock.
Deburr, Edge Break or Chamfer? Write a Drawing Note You Can InspectDistinguish unwanted burr removal from controlled edge geometry, and protect functional edges when specifying small turned components.
MAKE THE NEXT STEP SPECIFIC
Bring your part into the review.
Use this concept to explain your direction. Send the current drawing and the interfaces that determine how your component must work.
- Contact drawing with socket, insulator and termination interfaces
- Approved base alloy, complete coating specification and finished dimensions
- Quantities, dimensional records and connector-level validation responsibilities
CONNECT THE FORM TO THE PROCESS
Review the manufacturing route.
CONTINUE WITH SOURCE-LINKED REFERENCES
Explore related component forms.
Review the source and specifications shown on each reference page. Similar geometry does not establish this concept’s production or performance.
cs-product-038
Split contact pin
A slotted contact form for drawing-based power connector projects. Review the contact diameter, slot geometry and termination end together with the mating socket.
Explore component
cs-product-048
Brass solder-cup socket contact
A female contact reference for industrial circular connectors. Review the mating bore and solder-cup termination together so the contact fits both the mating pin and the intended wire.
Explore component
cs-product-036
PCB test receptacle socket
Replaceable test probes need a stable socket fit without making servicing difficult. Review the receiving bore, retention feature and solder tail against the mating probe and fixture plate.
Explore componentFROM EXAMPLE TO YOUR REQUIREMENT
Found something
close to your part?
Send your drawing
Use an example to explain your idea.
Your own drawing defines the final specification.
FROM COMPONENT TO PROJECT
Review the evidence. Define your part.
Start with the component geometry, then check what the drawing, sample and order records need to establish for your own part.
Send the current drawing with quantities and critical requirements. The review is the starting point for agreeing scope, quotation and sample approval.
Request a drawing review