Tube-contact profile
Define barb crest, entry lead and working length against the chosen tubing.
AI-generated engineering concept — not a production photograph. Final geometry is defined by your drawing.
ENGINEERING CONCEPT / cs-product-059
Retained hose-tail stem
A hose-tail stem concept with a through passage, rounded barbs and a separate retaining interface. Review the tubing contact and body retention as two connected assembly tasks.
- Buyer application
- Fluid control & equipment
- Reference type
- AI-generated geometry concept
- Material & process
- Options to review against your drawing
- Dimensions & tolerances
- Defined by your approved drawing
AI-generated engineering concept for a custom component discussion. It is not a production photograph, delivery case or completed inspection record.
FROM FORM TO A MANUFACTURING BRIEF
Match the tube-contact profile and device retention to the intended connection assembly.
A hose-tail stem concept with a through passage, rounded barbs and a separate retaining interface. Review the tubing contact and body retention as two connected assembly tasks.
01
Match the hose to the contact profile
Identify the intended tubing material, dimensions and installation method before freezing the barb form. Show the entry lead, crest shape and the length over which the tube contacts the stem. A drawing for a custom hose tail should not borrow a generic barb diameter without the mating-tube basis. If a clamp or another retention element is part of the design, include its location and assembly requirements.
02
Separate device retention from hose attachment
The opposite spigot has a different job: locating and retaining the stem in the receiving device. Specify the shoulder position, retaining groove and any sealing interface for that side. The concept does not define the retaining clip or prove that the connection swivels. Review wall section around the through passage and grooves together so the complete geometry, rather than only the visible barbs, enters the manufacturing discussion.
03
Approve the contact surfaces and assembly tests
Agree checks for the barb profile, passage, retaining groove and surfaces that contact the tube or seal. Define burr and cleanliness acceptance at the open ends. Tube pull-off, leakage and service durability require evaluation with the selected tube, retention parts and operating conditions. The component inspection should support those assembly tests while keeping material, drawing revision and sample identity traceable for repeat orders.
MATERIAL & PROCESS REVIEW
Select the material for the drawing and service
These are candidates to discuss, not an approved material specification. Confirm the grade, condition and final finish before quotation.
- Brass
- Specify the approved alloy, fluid compatibility requirements and any finishing restrictions.
- Stainless steel
- Review grade, tubing-contact surface and the manufacturing route for the complete profile.
The illustration does not establish a material grade, tolerance, coating or tested performance. Confirm these in your drawing and acceptance plan.
BEFORE APPROVING A SAMPLE
Agree what the checks need to establish.
Device-side retention
Specify the shoulder, groove and mating retaining element.
Passage and edges
Identify flow-path geometry, accessible edge checks and cleaning requirements.
Assembly validation
Agree tube attachment, leakage and retention tests for the completed connection.
BEFORE YOU RELEASE THE DRAWING
A practical next step.
Use these guides to define the records and checks your component needs.
Material Certificates and Lot Traceability for Machined Parts
Specify the evidence linking a material certificate to incoming stock, the machining job and the finished lot, while keeping chemistry checks separate from performance claims.
Cross-Hole Deburring of Turned Parts: Define Internal Edge AcceptanceSpecify hidden intersections, permitted edge changes and verification access so a turned fitting or contact component has an inspectable deburring requirement.
MAKE THE NEXT STEP SPECIFIC
Bring your part into the review.
Use this concept to explain your direction. Send the current drawing and the interfaces that determine how your component must work.
- Stem drawing and selected tube specification
- Receiving-device and retaining-part interfaces
- Material, finish and internal-edge requirements
- Quantities, assembly method and validation responsibility
CONNECT THE FORM TO THE PROCESS
Review the manufacturing route.
CONTINUE WITH SOURCE-LINKED REFERENCES
Explore related component forms.
Review the source and specifications shown on each reference page. Similar geometry does not establish this concept’s production or performance.
cs-product-042
Compact pneumatic fitting
A compact brass fitting with a threaded connection, hex section and through passage. Review the mating port, sealing arrangement and installation access against the actual pneumatic circuit.
Explore component
AI-assisted studio viewcs-product-007
Brass valve joint
A brass valve-joint form with a bored body and textured collar. Thread, sealing and interface requirements should be defined in your drawing.
Explore component
AI-assisted studio viewcs-product-051
Vacuum gripper adjustment stem
A hollow threaded stem reference for vacuum gripper positioning. Review adjustment travel, mounting threads and the internal passage as one interface before releasing your drawing.
Explore componentFROM EXAMPLE TO YOUR REQUIREMENT
Found something
close to your part?
Send your drawing
Use an example to explain your idea.
Your own drawing defines the final specification.
FROM COMPONENT TO PROJECT
Review the evidence. Define your part.
Start with the component geometry, then check what the drawing, sample and order records need to establish for your own part.
Send the current drawing with quantities and critical requirements. The review is the starting point for agreeing scope, quotation and sample approval.
Request a drawing review